Stand for papers

Agree that in a work disorder there is absolutely no place for a lot of pieces of paper with records that someday may still be useful. You always put them in one place, and in the end they are scattered all over the table. So it was with me, until I decided to make a paper holder in the technique of cardboard and a master class at the same time. The stand, of course, also serves to store blank paper. It's amazing what kind of things you can create with the help of cardboard, fabric and glue. The technique is simple, you just need to be patient and be careful. To create a stand you need to prepare: cardboard - 2 mm thickness; fabric, preferably 100% cotton; PVA glue; whatman; glue "Moment Crystal / Universal"; stationery knife; scissors; glue brush; masking tape; pencil; ruler.
tools and materials
We cut out the required size of cardboard with a stationery knife.
 parts of the stand
First, we will assemble three sides measuring 9x9 cm (two walls and the bottom of the stand), applying glue to the edges of the bottom.To the wall was at right angles, you can adjust it, propping the corner.
 glue the box
Sticking the back wall of the stand.
 glue the box
Take any round object and circle it on blanks for small front walls so that you get a beveled corner.
gluing m box
Glue small parts by applying glue to the edges of the walls and bottom.
glue the box
glue the box
This way the glued corners of the stand should look like.
 glue the box
The masking tape is needed to We secure the entire structure. We glue them all the joints inside the stand and outside. Using the stack, we smooth the adhesive tape so that there are no wrinkles.
 paste over
 paste over
We iron the workpiece from 39x13 cm size fabric.We will glue the fabric to the walls of the stand, as if wrapping it. Apply glue in a very thin layer on the first wall. If applied a lot, the glue can go through the fabric and leave marks or the cardboard can deform.
 paste
Sticking this wall to the fabric. We make sure that the wall lies just in the center and remains indented.
 Support for papers in cardboard technique
We glue everything three walls, carefully we glue small ones. We level the surface with a stack so that there is no blistering on the fabric.
 Stand for papers in cardboard technique
Cutting corners under sharp angle at the bottom of the stand. We seal indents. First you need to make cuts on the fabric in places where small walls end. We do not cut off the excess fabric, we glue the inside of the walls with it.
 Cardboard paper holder
Stand for paperwork using cardboard technique
In the same way, we cut and glue the corners of the upper part of the back and side wall support.
Stand for papers using cardboard technique
Now we will prepare a fabric in the front part to nicely glue small walls.
 Support for paperwork in cardboard technology
At the bottom, cut off the excess fabric to the level of the upper part of the bottom.
Stand for paper in cardboard technique
Making cuts accordingly.
 Stand for paper in the technique of cardboard packaging
first to seal the upper area, criss-crossing the perimeter rounded part. If there are extra folds, you can make small cuts by pasting them on each other.Fold and paste a piece of fabric that remains superfluous, but just serves for that purpose, so that the edge of the fabric is not visible. Gently glue the last part, forming a flat surface and corners with a stack.
 Support for papers in cardboard technique
Cut out from Whatman paper square, suitable for the size of the bottom and to it a fabric with allowances.
 Stand for papers in cardboard technique
On ironed the cloth leim Whatman. Cut corners at a sharp angle.
 Support for paperwork using cardboard technique
Leave the section that is not glued to the top parts of the bottom.
 Cardboard holder for paperwork technology
Glue the bottom, wrapping the loose fabric up.
 Stand for papers in cardboard technique
Level the surface with a stack. Stand for papers using cardboard technique Cut out four blanks for the inside of the stand from the drawing paper. They will be smaller in size than the walls by a few millimeters. Beforehand, it is better to apply each blank and make sure that it fits freely and another millimeter is in stock, because the fabric will also take place. We paste all the blanks with fabric.
 Stand for papers in the technique of cardboard
We glue the inside of the stand, well pressing and leveling surface stack.
 Cardboard holder for paperboard technology
Paper stand is ready! Now there will always be order on the table!
 Cardboard holder for paperwork
 Support for paper in cardboard technique


Related News


A Love Story: Wallis Simpson and Edward VIII
Gray mittens with a beautiful ornament
Pillow for working on a computer
Happy Birthday to Brother
7 best screenings of Stephen King