How to Build Stairs



Why choose wikiHow?
When you see the green expert checkmark on a wikiHow article, you know that the article has received careful review by a qualified expert. If you are on a medical article, that means that an actual doctor, nurse or other medical professional from our medical review board reviewed and approved it. Similarly, veterinarians review our pet articles, lawyers review our legal articles, and other experts review articles based on their specific areas of expertise.

How to Build Stairs

Three Parts:

Stairs are an essential part of many construction projects, from decks to interiors. It can seem daunting to think of making your own, but they’re actually made of just three main parts: stringers, treads, and risers. Stringers are diagonal 2 in × 12 in (5.1 cm × 30.5 cm) boards that support people's weight as they walk up the stairs. Treads are the top baseboards onto which you step, and risers are placed perpendicularly under each tread. Measure and cut the stringers accurately, and the other parts will mostly fall into place.

Steps

Making the Preliminary Measurements

  1. Measure the height of the area where you will install the stairs.This is also called the total rise. If you don’t plan to make the top step level with the area where the stairs begin, be sure to account for this gap in your measurement.
    • For example, if you are building stairs to go up to a deck, and you measure 3 feet (0.91 m) from the ground to the top of the deck, then this is the total rise.
    • If you want the stairs to stop 3 inches (7.6 cm) from the top of the deck, however, count the total rise as 2.75 feet (0.84 m).
  2. Divide the total rise by the typical rise per step.This will give you the total number of steps on your stairs. The typical rise per step is about 6.5–8 inches (17–20 cm), but you'll probably use a slightly different height for the actual rise.
    • For example, if your total rise is 95 inches (240 cm), divide it by 7 inches (18 cm) to get 13.53. Round down to get the number of steps: 13.
  3. Divide the total rise by the number of steps to get the actual rise per step.Remember this will probably be slightly different than the typical rise height. Finding the actual rise per step will ensure that your steps are all the same height, no matter what your overall rise is.
    • To continue with the same example, divide 95 inches (240 cm) by 13 steps to get 7.3125 inches (18.574 cm). On your stringer, each step will rise 7.3125 inches (18.574 cm).
  4. Establish the run of each step.The run (tread width) of each step should be no less than 9 inches (23 cm) and realistically at least 10 inches (25 cm). This allows enough space for the average foot to step comfortably and safely.
    • As a rule of thumb, the width of the treads and risers added together should equal between 16–18 inches (41–46 cm).
    • So, if your riser is 7 inches (18 cm) tall, your tread should be anywhere from 9–11 inches (23–28 cm) long.
  5. Find the total run of the staircase.The total run is the horizontal distance the stairs will travel from beginning to end. To find this, simply multiply the total number of steps by the run of each step.
    • For example, the total run in our hypothetical example is 130 inches (330 cm): 13 total steps x 10 inches (25 cm) (tread width) each = 130 inches (330 cm) total run.
  6. Decide if your stairs need landings.The longest boards suitable for building stairs will probably be 16 feet (4.9 m) long. This means you will probably max out at about every 14 steps. If your stairs have a long rise and run, you can install landings. However, you can install landings on any staircase, if you prefer.
    • If your staircase will have landings, consider each section of stairs as its own mini staircase.
  7. Calculate the length of the stringers.The stringers are the pieces of wood that will run diagonally underneath the length of the steps to hold them up. These are what your risers and treads will eventually be attached to. Determine their length the same way you determine the hypotenuse of a right triangle in geometry:
    • Multiply the horizontal length (run) by itself, multiply the height by itself, and add the two results together. Then, find the square root of this sum.
    • Keeping with the previous example, sqr(130 x 130) + (95 x 95) = 161 inches (409 cm)
  8. Determine how you will attach the stairs to the existing structure.If the stairs will sit flush with the vertical face of the structure, attach your stringers to the existing framework. However, if the stairs won’t sit flush with the existing structure (such as if they will attach to a deck with an overhang), be sure to either create a secondary support system or modify the tops of your stringers.
    • For example, if your stairs will mount beneath an overhang of a deck, making sure that the top step isn’t level with the top of the deck.
    • Instead, make the total rise slightly shorter and attach support posts to the top of the stringers.
  9. Count how many stringers you will need.To prevent your steps from sagging or bowing as you step on them, a wide staircase will need plenty of stringers underneath to keep it evenly supported. A very narrow staircase might be able to get away with having only two stringers, but it’s best to start at three and work your way up as necessary.
    • For safety reasons, the stringers should be spaced approximately 16 inches (40.6 cm) apart.
    • Wider staircases are generally preferable to narrower ones because they are much easier and more comfortable to navigate.

Cutting the Stringers

  1. Lay out a sufficiently long piece of 2 in × 12 in (5.1 cm × 30.5 cm) lumber.Don’t cut it down to length just yet. It will sit at an angle that depends on the height and depth of your steps, and the ends will have to be modified.
  2. Mark a carpenter's square to the height and depth of your steps.In our example, you would need to mark it at 7.3125 inches (18.574 cm) on one side by 10 inches (25 cm) on the other. Be sure you know which side corresponds with the height (riser) and which side corresponds with the depth (tread).
    • Look for stair gauges at a hardware store. These are small knobs you can attach to your carpenter’s square at the right measurements to make marking and cutting a breeze.
  3. Modify the top of the stringer to account for the overall angle.This angle will depend on the size of your steps. To do this properly:
    • Place the carpenter’s square over one corner of the lumber. Lay the side marking the height along the end of the lumber and the side marking the step depth along the length of the lumber.
    • Draw a line between the step-height and step-depth marks. This line marks the horizontal top of your stringer.
    • Mark the line so that its length is equivalent to the depth of one stair.
    • Use the square to draw a perpendicular line from the end of the board to the spot you just marked.
    • Cut along these lines.
  4. Measure and mark each step along the piece of lumber.Using the horizontal top of the stringer as a reference point, measure and draw a line down a distance equal to the height of one step. Then measure and draw a line across a distance equal to the depth of the step. Repeat this, moving downward until you’ve drawn the necessary number of steps.
  5. Use a circular saw or hand saw to cut the step notches.If using a circular power saw, cut to the edge of the marks on the stringers. Stop saw cuts – inch (0.32–0.64 cm) short of the opposite lines, then use a handsaw or jigsaw to finish.
  6. Square off the bottom of the stringer so that it will sit flush with the ground.Draw a line parallel to the top of the last step notch, and perpendicular to the side of it (where the bottom riser will eventually go). Cut this away to make the bottom of the stringer flush with the ground.
  7. Test the stringer by setting it in place.Cut the top and bottom of the stringer to fit, then test-fit it before cutting it out. Make sure the height is accurate. The stringer should sit flush with the ground or floor and also with the point at the top where it will attach to the existing structure.
  8. Use the first stringer as a template off of which to base the next stringers.Lay the first completed stringer down on a 2 in × 12 in (5.1 cm × 30.5 cm) board and simply trace the outline of the first stringer onto the other 2 in × 12 in (5.1 cm × 30.5 cm) boards. Then cut as necessary.

Assembling the Staircase

  1. Install the stringers.There are many ways to attach the tops of the stringers to the structure. One easy way is to screw metal joist hangers to the floor joists or deck supports. Drive screws through the holes in the joist hangers, putting one edge flush with the end of the stringer and the other against the joist.
    • Set the bottoms of the stringers on a firm footing like concrete, wood flooring, or even a block of treated lumber on top of gravel (for outside stairs).
  2. Secure and stabilize the stringers by installing risers (toe boards).Stringers are usually made from 1 in × 6 in (2.5 cm × 15.2 cm) wood. Though you can do without them, screwing these planks vertically between each step will make the stairs look nicer, and last longer.
    • Cut 1 in × 6 in (2.5 cm × 15.2 cm) boards to the width of your stairs. Secure each stringer with 2.5 in (6.4 cm) screws.
    • Ensure that the riser height is exactly the same for each step.
  3. Install the treads.Cut lumber to be at or slightly longer than the tread run in width, and as long as the stairs are wide (or just wider, if you prefer a slight overhang on the ends of your stairs. Secure the treads to the steps of the stringers with 2.5 in (6.4 cm) screws over each stringer.
    • For instance, you could cut 1 in × 10 in (2.5 cm × 25.4 cm) lumber to the width of the stairs, and use this for your treads.
    • For a special touch, use two boards and leave a – inch (0.32–0.64 cm) between them. For instance, you could cut 1 in × 5 in (2.5 cm × 12.7 cm) boards to the width of the stairs, and install two on each step, with a gap between them.
    • To make extra-strong steps place 2 in × 4 in (5.1 cm × 10.2 cm) boards on both sides of the center stringer under the treads.
  4. Attach trim boards to the outer stringers (optional).Trim boards can give your stairs a little more class by covering up the ends of the risers and treads. Cut 2 in × 12 in (5.1 cm × 30.5 cm) boards to the same length and angle as your stringers, but do not cut step notches into them. Place the cut lumber over the ends of your stairs, and fix into place with 2.5 in (6.4 cm) screws.
  5. Varnish, paint, or seal your stairs if necessary.Consider treating the wood against the elements, especially if the stairs will be outdoors. Even if you're building indoor-use stairs, finishing them will be a safeguard against everyday wear and tear, and beautify the end product.
    • Almost any varnish, stain, or paint will work just fine for stairs. You can also use non-slip paint or put non-slip adhesive pads on the stairs.

Community Q&A

Search
  • Question
    How do I support whole steps, on an existing open staircase in the basement in a very old home?

    Handyman
    Casey Dale Whitt is a Handyman in Florida. He has been the owner of Ablegator Handy Service since 2008.
    Handyman
    Expert Answer
    As long as the wood is solid you can use Simpson Strongtie wood brackets. They come in many varieties and styles and will very strongly fasten wood boards together.
    Thanks!
  • Question
    What material can I use under steps to quieten down the noisiness?
    wikiHow Contributor
    Community Answer
    Use a panel adhesive under each tread where it lays on top of stringers, before nailing. This is just like when framers (good framers that is) use same adhesive before installing decking to floor joists. This can be bought in caulking tubes at any lumber yard.
    Thanks!
  • Question
    How many steps should I make if they are 108 inches?
    wikiHow Contributor
    Community Answer
    Fifteen steps for 7 3/16" rise, or 14 for 7 3/4" rise. Remember that the stringer steps are one less than the actual steps. You could go with the 15, and 4 stringers if you knew a piano was being moved up them. 1/2" with 800+lbs makes a big difference. If the storm room is under the stairway, the extra stringers overhead can't hurt.
    Thanks!
  • Question
    Can a small staircase be supplied in kit form?
    wikiHow Contributor
    Community Answer
    Stringers of 3 to 5 steps can be purchased from your local lumber store. You can purchase them and the necessary step boards, cut to length, and assemble.
    Thanks!
  • Question
    How do I cut stringers when the bottom step is on a diagonal?
    wikiHow Contributor
    Community Answer
    The bottom run length will be longer on the outside step side. Chances are very good your beam itself will not be wide enough for it, so you will need to glue and brace some lumber on top face to compensate for the run. Rather than waste the money buying two feet longer beams for a run, if you needed 2.75", just build a shelf for first step and mounted stringers to it. This lets you use pressure treated lumber where it mounts to cement floor as well, solving two things with the one solution.
    Thanks!
  • Question
    Should use screws for raise and tread, or nails?
    Tom Medeiros
    Community Answer
    It really depends on how you will finish the stairs. Screws and liquid nails create the strongest and quietest stairs. If the treads will be stained, then liquid nails and finishing nails will create the best finished look. If you are carpeting them, screws or nails are fine.
    Thanks!
  • Question
    How can I make steps that are a little deeper?
    wikiHow Contributor
    Community Answer
    Your Increase the width of the stringer and tread. You can integrate the additional stringer by creating a channel on one stringer and a tongue on the other. Use an adhesive such as PL Premium.
    Thanks!
  • Question
    Can the stairs be made with TREX material?
    wikiHow Contributor
    Community Answer
    I wouldn't try to make stringers with it, but treads and risers wouldn't be a problem.
    Thanks!
Unanswered Questions
  • How do I make a plan to build stairs?
  • Why is it essential to make sure that a building is correctly set out before commencing of work?
  • How do I build stairs?
  • How do I build L or U-shaped stairs?
  • How do I attach the bottom of the stair (to a balcony) on a floor that is covered in ceramic tile?
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
  • Make sure the material you are using for the landing is in place before you lay out the steps to avoid trip hazards.

Warnings

  • Always check building codes that apply in your area. These may stipulate particular minimums or maximums for step runs and rises, the number of stringers that are necessary, etc.

Things You'll Need

  • Circular saw or crosscut hand saw
  • Carpenter framing square
  • Stair gauges
  • Corded or cordless drill
  • Screws (at least 2.5 inches (6.4 cm))
  • Metal floor joist hangers
  • 2 in × 10 in (5.1 cm × 25.4 cm) planks for stringers
  • 2 in × 6 in (5.1 cm × 15.2 cm) planks for steps
  • 1 in × 6 in (2.5 cm × 15.2 cm) planks for toe and foot boards

Related wikiHows

Sources and Citations

Made Recently

Loading...
Add a photo
Upload error
Awesome picture! Tell us more about it?

Article Info

Featured Article

Categories: |

In other languages:

Español: , Português: , Deutsch: , 中文: , Italiano: , Русский: , Français: , ไทย: , العربية: , Nederlands: , Tiếng Việt: 

Thanks to all authors for creating a page that has been read 717,273 times.
Did this article help you?
Expert Review By:
Handyman

of How to Build Stairs was reviewed by on March 23, 2019.

Co-authors:
Updated:
Views: 717,273
of readers found this articlehelpful.
2 votes - 100%
Click a star to add your vote
100% of people told us that this article helped them.

Quick Summary

To build stairs, start by cutting the stringers, which are the pieces ofwood that run diagonally under the stairs and hold them up. Then, install the stringers to the top and bottom of the area where you're building the stairs by screwing them into metal joists. Once the stringers are in place, install vertical risers between each step on the stringers. Then, secure the treads to the steps of the stringers, which is what you'll actually be stepping on when you use the stairs. Finally, apply a varnish, paint, or seal to the stairs to protect them against wear and tear.

Success Stories

J. B.

May 21, 2019

"Properly position the carpenter's square near one end of the lumber and lightly mark the apex of the square on thelumber. Draw a line parallel to the edge of the riser extending to the end. Set the apex of the square on the end of the lumber at the point where the horizontal line ends. This is now the location of the top step length. Otherwise a great article."

Ted Healy

Aug 24, 2019

"This helped a great deal. I've made steps before, but a long time ago. I found this site very good for me to jog mymemory. The steps turned out very good. Your site was very detailed and easy to understand. Thanks."

Lib Gillikin

Aug 1, 2019

"I have had three steps done, none correctly. Now, I think I will be a more Informed worker. I have learned what isrequired to do the job right."

John Gray

Jul 21, 2019

"The best I have seen. You progress at your own speed making it easy to digest every step. All instructions shouldbe designed as this one."

Cecilia O'Ryan

Sep 22, 2019

"This is great! I'm terrible at math, but this walked me through it with good graphics that really helped! Thanks!"
Rated this article:

Ace Fawaz

Jul 28, 2019

"A complete step by step, easy to understand instructions with illustrations that makes it easy to do. "

Jim Pinares

Jun 7, 2019

"This is very educational and easy to understand. I will recommend this article to anyone."

Thebe Mohasoane

Mar 10, 2019

"I was not sure where to start in constructing stairs, but now I have an idea."

Omoemu Festus

Aug 24, 2019

"It helped me by showing me the animation of how the stairs can be made. "
Rated this article:

Malcolm Adams

Jun 25, 2019

"The total construction illustration step by step was totally awesome!"

Z. R.

Apr 27, 2019

"Great info. Explained simply compared with a few other sources."

Elisa Fox

Sep 14, 2019

"Illustrations with each step helped a great deal. Thank you."

Scott Jaecques

Mar 18, 2019

"Now I know what I need to measure and how to lay it out."
Rated this article:

Lucius Simaai

Jul 29, 2019

"It helped on how to construct stairs."

Eileen T.






Video: How To Figure Length of Stair Stringer – Construction Math

How to Build Stairs
How to Build Stairs images

2019 year
2019 year - How to Build Stairs pictures

How to Build Stairs forecasting
How to Build Stairs recommendations photo

How to Build Stairs pictures
How to Build Stairs images

How to Build Stairs How to Build Stairs new picture
How to Build Stairs new foto

foto How to Build Stairs
pictures How to Build Stairs

Watch How to Build Stairs video
Watch How to Build Stairs video

Communication on this topic: How to Build Stairs, how-to-build-stairs/
Forum on this topic: How to Build Stairs, how-to-build-stairs/ , how-to-build-stairs/

Related News


What Is a Chalazion
Prince Harry and Meghan Markle throw rubber wellington boots in New Zealand
5 Jackets You Should Have In Your AutumnWinter Wardrobe
Woman Is Forced To Prove Shes Actually Lactating In The Middle Of An Airport
Salmon with Curry Yogurt Sauce
15-minute Creamy Avocado Pasta Recipe
How to Use a Eurorail Pass
Monkfish Curry Recipe
Are contact sports too dangerous
Understanding the Alphabet Soup of Lymphoma Treatment
Models Pose As Famous Works of Art
Suitcase Essentials: The Winter Getaway
How to Do a Dive
Are Yoga Classes Coming To A Waitrose Near You These Are The Stores Taking Part



Date: 07.12.2018, 10:27 / Views: 65451